![]() |
 |
 |
|
|
 |
|
|
 |
Tension Controller TC-2030 utilizes pulse generator to count the rotation number of roll on the unwinding or rewinding roller, according to the setting value of material’s thickness, calculating the change of diameter of unwinding or rewinding roll and reach the purpose of tension control. |
|
 |
• |
Function of 8 sets of control parameters of material. |
• |
Can be preset the initial tension, to modify the unstable condition in start, which is caused by mechanical friction. |
• |
Because of material characteristics, the control mode could be switched between manual control and automatic control. |
• |
Due to the requirement of production, the process could be switched between unwinding mode and rewinding mode. |
• |
It could be set the function of taping tension in the change of roll’s diameter. |
• |
Variety of control to drives: Magnetic Powder Brake · Clutch; Torque Controller · Vector Inverter · DC Motor Drive · Servo Motor Drive. |
|
 |
 |
 |
Tension controller TC-2030 |
 |
 |
System |
 |
Applicable mode |
Unwinding control, Rewinding control |
Rated output |
DC24V 4A max.; DC0 - 10V · DC0 - 5V 5mA max.
(Simulated signal output) |
Power |
AC 1∮, 220V, 50/60 Hz |
Surge current |
3A |
Power consumption |
150VA |
Ambient temperature |
0°C ~40°C |
Ambient humidity |
35% - 85% RH |
Vibration test |
Sweep freq. 10-55Hz, Displacement acceleration
0.5mm - 0.5G max. |
Withstand voltage |
1500V @ 1 minute |
Grounding way |
The third class grounding |
Environment requirement |
Not allowed corrosive gases, dust and rain |
Weight |
~ 3.5Kg |
Display |
LED |
Setting method |
Keypad |
|
 |
 |
Mechanic data |
 |
Mounting |
Desk-Mounted, Wall-Mounted, Surface-Mounted |
Dimension |
Refer to “Dimension Diagram” |
|
 |
 |
Electric data |
 |
Detector input |
Roll diameter Detector, DC 0~10V
Proximity switch DC12V |
Contact input |
Accelerated compensation, input impedance 6.6 KΩ
Decelerated compensation, input impedance 6.6 KΩ
Retention force, input impedance 6.6 KΩ
Tension setting selection (manual or automatic) , input impedance 6.6 KΩ
OUTPUT ON/OFF, input impedance 6.6 KΩ
Diameter RESET, input impedance 6.6 KΩ
RUN (START), input impedance 6.6 KΩ |
Contact output |
Low-tension, High-tension or Abnormal Alarm;
2 sets of output AC220V 1.0A |
Control output |
Magnetic powder brake (2 sets); DC 0~24V 4A
Tension-value signal, DC 0~5V or 0~10V 5mA max. |
|
|
 |
|
 |
 |
 |
 |
|
 |
 |
 |
|
 |
 |
|
![]() |
|
 |
Euntay Electric Co., Ltd. |
Motion Control System Manufacturer in Taiwan, |
Tension Control System Manufacturer in Taiwan, |
Edge Position Control System Manufacturer in Taiwan, |
Tension Controller, Load Cell , Tension Detector, Sensor |
Edge Position Controller, EPC, Edge Guide Sensor,Web Guiding, |
Ultrasonic EPC Detector , Infrared EPC Detector , Electric Cylinder , |
Hydraulic type Drive, Double loop Hydraulic Drive, Web Guide |
Web Guiding Machine, DC Motor Drive, Digital DC Motor Drive |
|
|
|
|